Siemens SIMATIC ET 200S: modular distributed I/O
SIMATIC ET 200S is Siemens' modular "slice-type" distributed I/O system: field signals are collected close to the machine and transmitted to the PLC via PROFIBUS DP or PROFINET. For years it was the standard in plants with SIMATIC S7-300 and S7-400, and it is still installed on a great many lines.
The E-Repair catalogue covers about 185 ET 200S part numbers.
⚙️ How an ET 200S station is built
- IM 151 interface module: connects the station to the fieldbus, for example IM 151-1 for PROFIBUS DP (also in a fibre-optic version) and IM 151-3 PN for PROFINET.
- Power modules: supply the groups of electronic modules that follow them.
- Electronic modules: digital and analogue inputs and outputs, 15 or 30 mm wide.
- PROFIsafe safety modules (F-DI, F-DO) for the machine's safety functions.
- TM terminal modules: the base into which the electronic modules are plugged and to which the field wiring is connected.
Separating the terminal module from the electronic module makes it possible to replace the electronics without disconnecting the wires: an important advantage when you need to act quickly.
🔍 Roots in the E-Repair catalogue
| Root | Function | Part numbers |
| 6ES7151-1, 6ES7151-3 | IM 151 interface modules (PROFIBUS DP, PROFINET) | 28 |
| 6ES7131-4 | Digital inputs | 16 |
| 6ES7132-4 | Digital outputs | 27 |
| 6ES7134-4 | Analogue inputs | 29 |
| 6ES7135-4 | Analogue outputs | 12 |
| 6ES7138-4 | Power modules, safety modules and special modules | 31 |
| 6ES7193-4 | TM terminal modules and accessories | 38 |
👉 6ES7151-1AA00-0AB0 – IM 151-1 PROFIBUS DP interface
👉 6ES7138-4FA00-0AB0 – F-DI PROFIsafe safety module
👉 6ES7193-4CA20-0AA0 – TM-E terminal modules
👉 Search the catalogue: 6ES7151 · 6ES7131-4 · 6ES7134-4 · 6ES7138-4
⚠️ Typical faults
- input or output channels damaged by overvoltages or short circuits in the field
- IM 151 interface modules losing communication with the PLC
- faulty power modules, which switch off a whole group of modules
- worn or oxidised terminal module contacts
- safety modules in error, stopping the machine for protection
🛠️ E-Repair services for SIMATIC ET 200S
As Approved Partner Siemens – Industry Services, E-Repair supports production continuity:
🔧 Component-level repair in E-Repair's certified in-house laboratory, with diagnosis and repair where technically feasible.
♻️ Refurbishment with replacement of components subject to ageing and functional testing according to the agreed scope of work.
🚚 Advance replacement with a refurbished or new product, if available in stock and after a compatibility check.
🛠️ On-site and remote technical assistance for diagnosis and recommissioning.
✅ Standard 12-month warranty on the services for which it applies, extendable up to 24 months under the applicable conditions.
❓ Frequently asked questions
✔️ Can just the electronic module be replaced?
Yes, in most cases the electronic module can be replaced without touching the wiring on the terminal module. Check that the part number is identical or compatible.
✔️ Do safety modules require special care?
Yes: after a replacement the PROFIsafe address and safety parameters must be checked according to the machine procedures.
✔️ What is needed for the diagnosis?
The full part number of the module, its position in the station and, if available, the PLC diagnostic message.
📚 Further reading
👉 SIMATIC ET 200 · 👉 ET 200B, ET 200L and ET 200X · 👉 SIMATIC S7-300
ℹ️ The information provided is general and indicative. Before purchase, installation or commissioning, check the data against the official Siemens documentation or contact E-Repair.
ES
DE
FR
IT 